Dell P152G Service Manual Download Page 44

Page: 44 / 102

Steps

1. Using the alignment posts, place the power button with fingerprint reader into its slot on the palmrest and keyboard

assembly.

2. Replace the (M2x2) screw that secures the power button with fingerprint reader to the palmrest and keyboard assembly.
3. Adhere the fingerprint reader Flexible Flat cable to the palmrest and keyboard assembly

NOTE:

Fold and align the fingerprint reader Flexible Flat cable to the mark at the right of the power button, and align

the white line on the Flexible Flat cable to the mark on the palmrest and keyboard assembly.

4. Close the display hinge.
5. Replace the two (M2.5x5) screws that secure the display hinge to the palmrest and keyboard assembly.

Next steps

1. Install the

2. Install the

3. Install the

4. Install the

5. Install the

6. Follow the procedure in

After working inside your computer

Display assembly

Removing the display assembly (Aluminum)

Prerequisites

1. Follow the procedure in

Before working inside your computer

2. Remove the

SD card

3. Remove the

base cover

About this task

The following images indicate the location of the display assembly and provide a visual representation of the removal procedure.

Removing and installing components

Summary of Contents for P152G







































































































Search results

Summary of Contents for P152G

Reviews:

Related manuals for P152G

Brands by name

Popular brands

Dell P152G, Service Manual

Search results

Summary of Contents for P152G

Reviews:

Related manuals for P152G

Brands by name

Popular brands