background image

Steps

1. Using the alignment posts, place the speakers on the palm-rest and keyboard assembly.

NOTE:

 Ensure that the alignment posts are threaded through the rubber grommets on the speaker.

2. Route the speaker cable through the routing guides on the palm-rest and keyboard assembly.
3. Connect the speaker cable to the system board.
4. Adhere the adhesive tape to secure the speaker cable.

Next steps

1. Install the 

battery

.

2. Install the 

base cover

.

3. Install the 

SD card

.

4. Follow the procedure in 

After working inside your computer

.

Power-button board

Removing the power button with optional fingerprint reader

Prerequisites

1. Follow the procedure in 

Before working inside your computer

.

2. Remove the 

SD card

.

3. Remove the 

base cover

.

4. Remove the 

SSD

.

5. Remove the 

wireless card

.

6. Remove the 

I/O board

.

About this task

The following images indicate the location of the power button with optional fingerprint reader and provides a visual
representation of the removal procedure.

42

Removing and installing components

Summary of Contents for P152G







































































































Reviews: