Dell P132G Service Manual Download Page 23 | Manualshive

Page: 23 / 83

background image

Steps

1. Remove the seven (M2.5x5) screws and loosen the two captive screws from the base cover.
2. Pry open the base cover starting from the recesses located in the U-shaped indents at the top edge of the base cover near

the hinges.

NOTE:

CAUTION: DO NOT pry up from the edge near the vents at the top side of the base cover as this may damage

the base cover.

3. Lift up the top side of the base cover and remove it from the system.

Installing the base cover

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

Disassembly and reassembly

23

«
...
21
22
23
24
25
...
»

Summary of Contents for P132G




















































































Reviews:

No comments

Related manuals for P132G

Brand: IBM Pages: 8

VisionBook 12Wa

Brand: UMAX Technologies Pages: 34

Brand: Gigabyte Pages: 387

Brand: Acer Pages: 75

Brand: Acer Pages: 182

Brand: Acer Pages: 182

Brand: Acer Pages: 194

Brand: Acer Pages: 30

Brand: Acer Pages: 73

Inspiron 14 5458

Brand: Dell Pages: 101

Brand: Dell Pages: 123

Brand: Dell Pages: 106

Brand: Fujitsu Pages: 99

Brand: Fujitsu Pages: 78

S7220 - LifeBook - Core 2 Duo 2.4 GHz

Brand: Fujitsu Pages: 208

A305-S6834 - Satellite - Core 2 Duo 1.83 GHz

Brand: Toshiba Pages: 3

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands