Dell Networking S6000 System Reference Manual Download

Page: 984 / 1510

graceful-restart helper-reject

Specify the OSPF router to not act as a helper during graceful restart.

S6000

Syntax

graceful-restart helper-reject

ip-address

To return to default value, use the

no graceful-restart helper-reject

command.

Parameters

ip-address

Enter the OSPF router-id, in IP address format, of the restart
router that

will not

act as a helper during graceful restart.

Defaults

Not configured.

Command
Modes

ROUTER OSPF

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version
8.3.12.0

Introduced on the S4810.

Version 7.8.1.0

Restart role

enabled on the S-Series (Both

Helper

and

Restart

roles now supported on S-Series). Added support

for Multi-Process OSPF.

Version 7.7.1.0

Added

Helper-Role

support on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

pre-Version
6.1.1.1

Introduced on the E-Series.

graceful-restart mode

Enable the graceful restart mode.

S6000

Syntax

graceful-restart mode [planned-only | unplanned-only]

984

Open Shortest Path First (OSPFv2 and OSPFv3)

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands