Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 98 / 1510

background image

Version 7.5.1.0

Introduced on the C-Series.

E-Series

Original command.

ip tftp vrf

Configures an TFTP client with a VRF that is used to connect to the TFTP server.

Syntax

ip tftp [vrf

vrf-name

]

To undo the TFTP client configuration, use the

no ip tftp [vrf

vrf-name

]

command.

Parameters

vrf

vrf-name

Enter the keyword

vrf

and then the name of the VRF to

specify the VRF that is used by the TFTP client.

Defaults

Disabled

Command
Modes

CONFIGURATION

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

FTOS Command Line Reference Guide

.

The following is a list of the FTOS version history for this command.

Version 9.4.
(0.0)

Introduced on the S-Series and Z-Series.

Usage
Information

Use this command to make the TFTP clients VRF aware. The VRF name that you
specify is used by the TFTP client to reach the TFTP server. If no VRF is specified,
then the default VRF is used.

Related
Commands

ftp-server topdir

— sets the directory to be used for incoming FTP connections to

the E-Series.

ftp-server username

— sets a username and password for incoming FTP

connections to the E-Series.

98

Control and Monitoring

«
...
96
97
98
99
100
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

Brand: N-Tron Pages: 20

Brand: H3C Pages: 13

Brand: H3C Pages: 207

Brand: H3C Pages: 62

Draco major K474-U8/C8

Brand: Ihse Pages: 167

Brand: steute Pages: 10

Brand: I-Tech Pages: 39

PMV WM Ultraswitch

Brand: Flowserve Pages: 16

EXHL-TRN-LE1 Series

Brand: Larson Electronics Pages: 2

SISTG1040-242-LRT

Brand: Transition Networks Pages: 31

Brand: Vega Pages: 44

OSD2700F SERIES

Brand: Optical Systems Pages: 29

Brand: Lantech Pages: 29

Brand: TRENDnet Pages: 2

Brand: Broadcast Pix Pages: 478

Brand: Lancom Pages: 21

Brand: Racal Instruments Pages: 53

ENTERTAINMENT HUB

Brand: Ev-ent Hire Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands