Dell Networking S6000 System Reference Manual Download

Page: 966 / 1510

no-summary

(OPTIONAL) Specify that no summary LSAs should be sent
into the NSSA.

Defaults

Not configured.

Command
Modes

ROUTER OSPF

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.8.1.0

Added support for the Multi-Process OSPF.

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

pre-Version
6.1.1.1

Introduced on the E-Series.

area range

Summarize routes matching an address/mask at an area border router (ABR).

S6000

Syntax

area

area-id

range

ip-address mask

[not-advertise]

To disable route summarization, use the

no area

area-id

range

ip-address

mask

command.

Parameters

area-id

Specify the OSPF area in dotted decimal format (A.B.C.D.) or
enter a number from zero (0) to 65535.

ip-address

Specify an IP address in dotted decimal format.

mask

Specify a mask for the destination prefix. Enter the full mask
(for example, 255.255.255.0).

not-advertise

(OPTIONAL) Enter the keywords

not-advertise

to set the

status to DoNotAdvertise (that is, the Type 3 summary-LSA is
suppressed and the component networks remain hidden
from other areas.)

966

Open Shortest Path First (OSPFv2 and OSPFv3)

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands