Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 959 / 1510

background image

Version 7.8.1.0

Introduced on the C-Series.

Version 7.6.1.0

Introduced on the E-Series.

Usage
Information

This feature allows you to limit the number of multicast entries on the system. This
number is the total of all the multicast entries on all line cards in the system. On
each line card, the multicast module only installs the maximum number of entries,
depending on the configured CAM profile.
To store multicast routes, use the IN-L3-McastFib CAM partition. It is a separate
hardware limit that exists per port-pipe. This hardware space limitation can
supersede any software-configured limit. The opposite is also true, the CAM
partition might not be exhausted at the time the system-wide route limit set by the

ip multicast-limit

command is reached.

Related
Commands

show ip igmp groups

— shows the IGMP groups.

ip multicast-routing

Enable IP multicast forwarding.

S6000

Syntax

ip multicast-routing

To disable multicast forwarding, use the

no ip multicast-routing

command.

Defaults

Disabled.

Command
Modes

CONFIGURATION

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.1

Introduced on the S4810.

E-Series legacy
command

Usage
Information

After you enable multicast, you can enable IGMP and PIM on an interface. In
INTERFACE mode, enter the

ip pim sparse-mode

command to enable IGMP

and PIM on the interface.

Multicast

959

«
...
957
958
959
960
961
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

Brand: Eaton Pages: 8

Brand: KanexPro Pages: 16

Brand: Radial Engineering Pages: 8

Brand: Radial Engineering Pages: 2

Brand: FLIR Pages: 2

Brand: ATZ Pages: 8

EXT-DVIKVM-441DL

Brand: Gefen Pages: 32

TM-1-8210 Series

Brand: Eaton Pages: 3

Brand: J-Tech Digital Pages: 28

Brand: Generac Power Systems Pages: 20

Brand: Kramer Pages: 2

Brand: CIECO Pages: 17

Brand: JetNet Pages: 20

Brand: nedis Pages: 24

AVS-OCT-3264-360

Brand: AMX Pages: 1

Brand: Abtus Pages: 4

Brand: PortaOne Pages: 78

Gigabit Switch 8

Brand: 3Com Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands