Dell Networking S6000 System Page 902 Reference Manual Download

Page: 902 / 1510

Defaults

none

Command
Modes

EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.5.1.0

Added support for 4-port 40G line cards on ExaScale.

Version 8.3.7.0

Introduced on the S4810.

Version 7.7.1.0

Introduced on the S-Series.

Version 7.6.1.0

Introduced on the C-Series.

Version 7.4.1.0

Introduced on the E-Series.

disable

Enable or disable LLDP.

S6000

Syntax

disable

To enable LLDP, use the

no disable

command.

Defaults

Enabled, that is no disable.

Command
Modes

CONFIGURATION (conf-lldp) and INTERFACE (conf-if-

interface

-lldp)

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.7.1.0

Introduced on the S-Series.

902

Link Layer Discovery Protocol (LLDP)

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands