Dell Networking S6000 System Page 891 Reference Manual Download | Manualshive

Page: 891 / 1510

background image

Parameters

seconds

Enter a number as the time between FEFD control packets.
The range is from 3 to 300 seconds. The default is

15

seconds

.

Defaults

15 seconds

Command
Modes

INTERFACE

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Legacy E-
Series
command.

Related
Commands

•

— enables far-end failure detection.

fefd mode

Change the FEFD mode on an interface.

Syntax

fefd mode {normal | aggressive}]

To return the FEFD mode to the default of normal, use the

no fefd mode

command.

Parameters

normal

(OPTIONAL) Enter the keyword

normal

to change the link

state to “unknown” when a far-end failure the software
detects on that interface. When the interface is placed in
“unknown” state, the software brings down the line protocol.

aggressive

(OPTIONAL) Enter the keyword

aggressive

to change the

link state to “error-disabled” when a far-end failure the
software detects on that interface. When an interface is
placed in “error-disabled” state, enter the

fefd reset

command to reset the interface state.

Defaults

normal

Layer 2

891

«
...
889
890
891
892
893
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

Brand: TAMS Pages: 28

Brand: LEGRAND Pages: 2

MyPower S2300-28TC-AC

Brand: Maipu Pages: 31

Brand: Edge-Core Pages: 9

Brand: Xantech Pages: 4

Elinx EIR418-2SFP-T

Brand: B&B Electronics Pages: 25

Brand: CIS Pages: 3

ProSAFE JGS516PE

Brand: NETGEAR Pages: 2

Brand: Abseco Pages: 10

Allen-Bradley 800F-ALR1

Brand: Rockwell Automation Pages: 2

Brand: FS Pages: 43

Hi-Speed USB 2.0 Hub

Brand: Saitek Pages: 14

Brand: Linkskey Pages: 2

Brand: NegoRack Pages: 41

Brand: Comet Labs Pages: 46

Brand: Xcellon Pages: 2

Brand: DigitalZone Pages: 20

XGS-6350-12X8TR

Brand: Planet Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands