Dell Networking S6000 System Reference Manual Download

Page: 888 / 1510

debug fefd

Enable debugging of FEFD.

S6000

Syntax

debug fefd {events | packets} [

interface

]

To disable debugging of FEFD, use the

no debug fefd {events | packets}

[

interface

]

command.

Parameters

events

Enter the keyword

events

to enable debugging of FEFD

state changes.

packets

Enter the keyword

packets

to enable debugging of FEFD to

view information on packets sent and received.

interface

(OPTIONAL) Enter the following keywords and slot/port or
number information:

• For a 10-Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

then the slot/port information.

• For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

then the slot/ port information.

Command
Modes

EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version
8.3.12.0

Introduced on the S4810.

Legacy E-
Series
command.

Related
Commands

•

fefd

— enables far-end failure detection on an interface.

•

fefd reset

— enables FEFD globally on the system.

888

Layer 2

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands