manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual, Page: 834 / 1510

Share
Download
Dell Networking S6000 System Reference Manual Download Page 834

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 
8.3.12.0

Introduced on the S4810.

Version 7.8.1.0

Introduced.

net

To configure an IS-IS network entity title (NET) for a routing process, use this mandatory command. If 

you did not configure a NET, the IS-IS process does not start.

S6000

Syntax

net 

network-entity-title

To remove a net, use the 

no net network-entity-title

 command.

Parameters

network-
entity-title

Specify the area address and system ID for an IS-IS routing 
process. The first 1 to 13 bytes identify the area address. The 
next 6 bytes identify the system ID. The last 1 byte is the 
selector byte, always identified as zero zero (00). This 
argument can be applied to an address or a name.

Defaults

Not configured.

Command 
Modes

ROUTER ISIS

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 
8.3.19.0

Introduced on the S4820T.

Version 
8.3.12.0

Introduced on the S4810.

Version 8.3.11.1

Introduced on the Z9000.

834

Intermediate System to Intermediate System (IS-IS)

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments