Dell Networking S6000 System Reference Manual Download

Page: 783 / 1510

ipv6 control-plane egress-filter

Enable egress Layer 3 ACL lookup for IPv6 CPU traffic.

S6000

Syntax

ipv6 control-plane egress-filter

Defaults

Not enabled.

Command
Modes

EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 9.0.0.0

Introduced on the Z9000.

Version
8.3.19.0

Introduced on the S4820T.

Version
8.3.10.0

Introduced on the S4810.

ipv6 access-list

Configure an access list based on IPv6 addresses or protocols.

S6000

Syntax

ipv6 access-list

access-list-name

cpu-qos {permit | deny}

ospfv3

To delete an access list, use the

no ipv6 access-list

access-list-name

command.

Parameters

access-list-
name

Enter the access list name as a string, up to 140 characters.

cpu-qos

Enter the keyword

cpu-qos

to assign this ACL to control

plane traffic only (CoPP).

permit

Enter the keyword

permit

to configure a filter to forward

packets meeting this condition.

deny

Enter the keyword

deny

to configure a filter to drop packets

meeting this condition.

IPv6 Access Control Lists (IPv6 ACLs)

783

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands