manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual

Share
Download
Dell Networking S6000 System Reference Manual Download Page 778

25

IPv6 Access Control Lists (IPv6 ACLs)

IPv6 ACLs and IPv6 Route Map commands are supported on Dell Networking platform.

NOTE: For IPv4 ACL commands, refer to the 

Access Control Lists (ACL)

 chapter.

Important Points to Remember

• Certain platforms require manual CAM usage space allotment. For more information, refer to the 

cam-acl

 command.

• Egress IPv6 ACL and IPv6 ACL on the Loopback interface is not supported.
• Reference to an empty ACL permits any traffic.
• ACLs are not applied to self-originated traffic (for example, Control Protocol traffic not affected by 

IPv6 ACL because the routed bit is not set for Control Protocol traffic and for egress ACLs the routed 

bit must be set).

• You can use the same access list name for both IPv4 and IPv6 ACLs.
• You can apply both IPv4 and IPv6 ACLs on an interface at the same time.
• You can apply IPv6 ACLs on physical interfaces and a logical interfaces (Port-channel/VLAN).
• Non-contiguous masks are not supported in source or destination addresses in IPv6 ACL entries.
• Because the prefix mask is specified in /x format in IPv6 ACLs, inverse mask is not supported.

show cam-acl-egress

Show information on FP groups allocated for egress ACLs.

S6000

Syntax

show cam-acl-egress

Command 
Modes

• EXEC
• EXEC Privilege

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

778

IPv6 Access Control Lists (IPv6 ACLs)

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands