Dell Networking S6000 System Reference Manual Download

Page: 770 / 1510

0 unknown protocol, 0 not a gateway

0 security failures, 0 bad options

Frags: 0 reassembled, 0 timeouts, 0 too big

0 fragmented, 0 couldn't fragment

Bcast: 28 received, 0 sent; Mcast: 0 received, 0 sent

Sent: 16048 generated, 0 forwarded

21 encapsulation failed, 0 no route

ICMP statistics:

Rcvd: 0 format errors, 0 checksum errors, 0 redirects, 0

unreachable

0 echo, 0 echo reply, 0 mask requests, 0 mask replies, 0

quench

0 parameter, 0 timestamp, 0 info request, 0 other

Sent: 0 redirects, 0 unreachable, 0 echo, 0 echo reply

0 mask requests, 0 mask replies, 0 quench, 0 timestamp

0 info reply, 0 time exceeded, 0 parameter problem

UDP statistics:

Rcvd: 0 total, 0 checksum errors, 0 no port

0 short packets, 0 bad length, 0 no port broadcasts, 0

socket full

Sent: 0 total, 0 forwarded broadcasts

TCP statistics:

Rcvd: 23829 total, 0 checksum errors, 0 no port

Sent: 16048 total

ARP statistics:

Rcvd: 156 requests, 11 replies

Sent: 21 requests, 10 replies (0 proxy)

Routing Processor1 IP Traffic:

show tcp statistics

View information on TCP traffic through the switch.

S6000

Syntax

show tcp statistics {all | cp | rp1 | rp2}

Parameters

all

Enter the keyword all to view

all

TCP information.

Enter the keyword

to view only TCP information from the

Control Processor.

rp1

Enter the keyword

rp1

to view only TCP statistics from

Route Processor 1.

rp2

Enter the keyword

rp2

to view only TCP statistics from

Route Processor 2.

Command
Modes

EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

770

IPv4 Routing

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands