Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 562 / 1510

background image

lacp fast-switchover

Cause the physical ports to be aggregated faster by configuring this capability in a port-channel on both
the nodes that are members of a port-channel.

S6000

Syntax

lacp fast-switchover

To disable the capability of faster aggregation of the member ports of a LAG or a
port-channel bundle, use the no version of this command.

Defaults

Not configured

Command
Modes

INTERFACE (conf-if-po-number)

Command
History

Version 9.3(0.0)

Introduced on the S6000.

Usage
Information

You can configure the optimal switchover functionality for LACP even if you do not
enable the fast boot mode on the system. You must configure the long timeout
mechanism for the LACP session to enable the fast boot capability to operate
properly. This command applies to dynamic port-channel interfaces only. When
applied on a static port-channel, this command has no effect.

If you configure the optimized booting-time capability and perform a reload of the
system, the LACP application sends PDUs across all the active LACP links
immediately.

Related
Commands

— displays the LACP configuration.

encapsulation dot1q

Configures lite-subinterfaces. This command is supported on the S6000 platform.

Syntax

encapsulation dot1q

vlan-id

To remove a previously configured lite-subinterface, use the

no

version of this

command.

Parameters

dot1q

vlan-id

Enter the keyword

dot1q

followed by the VLAN ID to which

the host belongs. The range is from 1 to 4094. A lite
subinterface is considered as a Layer 3 port property and is
synchronous with the existing rules of applying Layer 2 or
Layer 3 properties to an interface.

Command
Modes

INTERFACE

562

Flex Hash and Optimized Boot-Up

«
...
560
561
562
563
564
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

Brand: IBM Pages: 44

Brand: Valcom Pages: 2

Brand: Kramer Pages: 61

Celabs Distribution Hub and Receiver

Brand: Cable Electronics Pages: 2

Brand: Sams Pages: 14

Brand: PKP Pages: 11

Brand: Grizzly Pages: 2

CT-HDVD-4X14K-SW

Brand: NB Pages: 23

Brand: Atlona Pages: 13

Brand: SMART-AVI Pages: 9

Brand: Watt Stopper Pages: 2

FASTHOME 550-030

Brand: Steren Pages: 4

enbrighten 51253

Brand: Jasco Pages: 2

IntraCore IC39240

Brand: Asante Pages: 3

Brand: TRENDnet Pages: 2

Brand: Grandbeing Pages: 27

Brand: Elk Products Pages: 2

Brand: Kramer Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands