manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual, Page: 465 / 1510

Share
Download
Dell Networking S6000 System Reference Manual Download Page 465

dcb-policy output

Apply the output policy with the ETS configuration to an egress interface.

S6000

Syntax

dcb-policy output 

policy-name

To delete the output policy, use the 

no dcb-policy output

 command.

Parameters

policy-name

Enter the output policy name.

Defaults

none

Command 
Modes

INTERFACE

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 
8.3.19.0

Introduced on the S4820T.

Version 
8.3.12.0

Introduced on the S4810.

Version 
8.3.16.0

Introduced on the MXL 10/40GbE Switch IO Module.

Usage 
Information

NOTE: Please note that Dell Networking does not recommended to use this 
command as it has been deprecated in the current 9.4.(0.0) release. A warning 
message appears when you try to run this command indicating that you have 
to use the dcb-map commands in the future.

When you apply an ETS output policy to on interface, ETS-configured scheduling 
and bandwidth allocation take precedence over any configured settings in QoS 
output policies.

When you disable DCB, ETS is disabled by default. When you enable DCB, ETS is 
enabled for all interfaces that have the default ETS configuration applied (all dot1p 
priorities in the same group with equal bandwidth allocation).

Related 
Commands

dcb-output

 — creates a DCB output policy.

Data Center Bridging (DCB)

465

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments