Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 265 / 1510

background image

Defaults

By default, 10 ACL logs are generated if you do not specify the threshold explicitly.

The default frequency at which ACL logs are generated is five minutes. By default,
flow-based monitoring is not enabled.

Command
Modes

CONFIGURATION-EXTENDED-ACCESS-LIST

Command
History

Version 9.4(0.0)

Added the support for flow-based monitoring on the S4810,
S4820T, S6000, and Z9000 platforms.

Version 9.3(0.0)

Added the support for logging of ACLs on the S4810,
S4820T, and Z9000 platforms.

Usage
Information

When the configured maximum threshold is exceeded, generation of logs is
stopped. When the interval at which ACL logs are configured to be recorded
expires, the subsequent, fresh interval timer is started and the packet count for that
new interval commences from zero. If ACL logging was stopped previously
because the configured threshold is exceeded, it is re-enabled for this new interval.

If ACL logging is stopped because the configured threshold is exceeded, it is re-
enabled after the logging interval period elapses. ACL logging is supported for
standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure
ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable
logging for ACLs that are associated with egress interfaces.

You can activate flow-based monitoring for a monitoring session by entering the
flow-based

enable

command in the Monitor Session mode. When you enable this

capability, traffic with particular flows that are traversing through the ingress and
egress interfaces are examined and, appropriate ACLs can be applied in both the
ingress and egress direction. Flow-based monitoring conserves bandwidth by
monitoring only specified traffic instead all traffic on the interface. This feature is
particularly useful when looking for malicious traffic. It is available for Layer 2 and
Layer 3 ingress and egress traffic. You may specify traffic using standard or
extended access-lists. This mechanism copies all incoming or outgoing packets on
one port and forwards (mirrors) them to another port. The source port is the
monitored port (MD) and the destination port is the monitoring port (MG).

Related
Commands

— assigns a filter to deny IP traffic.

— assigns a filter to deny UDP traffic.

deny ether-type (for Extended MAC ACLs)

Configure an egress filter that drops specified types of Ethernet packets on egress ACL supported line
cards. (For more information, refer to your line card documentation).

Syntax

deny ether-type

protocol-type-number

{

destination-mac-address

mac-address-mask

| any} vlan

vlan-id

{

source-mac-address mac-

Access Control Lists (ACL)

265

«
...
263
264
265
266
267
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

Brand: Water Witch Pages: 2

Brand: Kathrein Pages: 8

Brand: Nayar Systems Pages: 21

Brand: Kathrein Pages: 24

Brand: Kasia Pages: 5

Brand: Qlogic Pages: 4

Brand: rako Pages: 4

Brand: DAITEM Pages: 37

Brand: Black Box Pages: 28

Brand: Eaton Pages: 43

MicroHub GUH274W3

Brand: IOGear Pages: 1

Brand: W Box Technologies Pages: 10

Brand: Cabletron Systems Pages: 56

Brand: Clare Controls Pages: 2

Brand: Blackberry Pages: 10

Lanolinx LNX-1002GN

Brand: ANTAIRA Pages: 110

Brand: SICK Pages: 64

BZ-UHD-88M100-ARC

Brand: BZB Gear Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands