manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual

Share
Download
Dell Networking S6000 System Reference Manual Download Page 227

Version 9.0.2.0

Introduced on the S6000.

Version 
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 8.1.1.0

Introduced on the E-Series ExaScale.

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

pre-Version 
6.1.1.0

Introduced on the E-Series.

Usage 
Information

Sequence numbers for this filter are automatically assigned starting at sequence 
number 5.

If you do not use the 

ge

 or 

le

 options, only packets with an exact match to the 

prefix are filtered.

ip prefix-list

Enter the PREFIX-LIST mode and configure a prefix list.

S6000

Syntax

ip prefix-list 

prefix-name

To delete a prefix list, use the 

no ip prefix-list 

prefix-name

 command.

Parameters

prefix-name

Enter a string up to 16 characters long as the name of the 
prefix list, up to 140 characters long.

Command 
Modes

CONFIGURATION

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 8.1.1.0

Introduced on the E-Series ExaScale.

Access Control Lists (ACL)

227

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands