Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 1455 / 1510

background image

proxy-gateway static

Configure the VLT static proxy gateway

S6000

Syntax

[no] proxy-gateway static

Command
Modes

VLT DOMAIN

Command
History

Version 9.4(0.0)

Introduced on the S4810, S4820T, S6000, Z9000, and MXL
Switch.

Usage
Information

When proxy-gateway static configuration is made, the setting is saved in the Layer
2 application. When you remove the static proxy gateway configuration, each
proxy-gateway static mac configured is deleted and also the notification to delete
the local destination address (DA) configured is sent to the Layer 2 module. When
remote-mac-address

mac-address-identifier

configuration is made, the MAC

details are saved. When no remote-mac-address

mac-address-identifier

configuration is made, the MAC details and the local DA information are deleted.

Example

Dell(conf)#vlt-domain 1

Dell(conf-vlt-domain#proxy-gateway static

remote-mac-address exclude-vlan

Configure the proxy-gateway static entry and exclude a VLAN or a range of VLANs from proxy routing.

S6000

Syntax

remote-mac-address

mac—address

exclude-vlan

vlan-range

Parameters

remote-mac-
address

Specify the remote MAC address for a static proxy gateway.

mac-address

Enter the 48-bit hexadecimal address in nn:nn:nn:nn:nn:nn
format.

vlan-range

Enter the member VLANs using comma-separated VLAN IDs,
a range of VLAN IDs, a single VLAN ID, or a combination. For
example:

Comma-separated: 3, 4, 6

Range: 5-10

Combination: 3, 4, 5-10, 8

VLT Proxy Gateway

1455

«
...
1453
1454
1455
1456
1457
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

Brand: Datavideo Pages: 4

Brand: Datavideo Pages: 66

Brand: Zektor Pages: 17

Brand: Ruby Tech Pages: 2

IPES-3424DSFP-2P

Brand: Lantech Pages: 26

IES2016-16T Series

Brand: 3onedata Pages: 3

ServicePlus S11

Brand: Horstmann Pages: 8

Brand: Kramer Pages: 4

Brand: ZIMCO Pages: 7

Brand: Goobay Pages: 2

Brand: Blue Sea Systems Pages: 2

EZ HUB 10/100 5608DS

Brand: SMC Networks Pages: 2

QSW-M2108 Series

Brand: QNAP Pages: 28

CrossPoint 42 HVA

Brand: Extron electronics Pages: 46

Brand: Kramer Pages: 85

Brand: Novus Pages: 16

Brand: EMP-Centauri Pages: 4

Brand: Xantech Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands