Dell Networking S6000 System Reference Manual Download

Page: 1452 / 1510

show ip vrf

Displays information corresponding to the VRFs that are configured in the system.

Syntax

show ip [vrf

vrf-name

]

Parameters

vrf

vrf-name

Enter the keyword vrf and then the name of the VRF to
display information corresponding to that VRF..

Command
Modes

EXEC

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.4.
(0.0)

Introduced on the S-Series and Z-Series.

Version 8.2.1.0

Introduced on the E-Series.

Example

show ip vrf

VRF-Name VRF-ID Interfaces

default 0 Te 0/0-13,18-47,

Fo 0/48,52,56,60,

Ma 0/0,

Ma 1/0,

Ma 2/0,

Ma 3/0,

Ma 4/0,

Ma 5/0,

Ma 6/0,

Ma 7/0,

Ma 8/0,

Ma 9/0,

Ma 10/0,

Ma 11/0,

Nu 0,

Vl 1

test1 1 Te 0/14,16-17

test2 2 Te 0/15

management 64

FTOS#show ip vrf test1

VRF-Name VRF-ID Interfaces

test1 1 Te 0/14,16-17

1452

Virtual Routing and Forwarding (VRF)

«
...
1450
1451
1452
1453
1454
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands