Dell Networking S6000 System Reference Manual Download Page 141

Page: 141 / 1510

Version
8.3.12.0

Introduced on the S4810. Added support for

source-

interface

for link-local IPv6 addressing.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.2.1.0

Introduced on the E-Series ExaScale (IPv6). Increased the
number of VLANs on ExaScale to 4094 (was 2094).

Version 8.1.1.0

Introduced on the E-Series ExaScale (IPv4).

Version 7.9.1.0

Introduced VRF.

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series and added support for IPv6
address on the E-Series only.

Example

Dell(conf)#do telnet vrf vrf1 10.10.10.2

telnet-peer-stack-unit

Open a Telnet connection to the peer stack unit.

Syntax

telnet-peer-stack-unit

Defaults

Not configured.

Command
Modes

• EXEC
• EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 9.0.0.0

Introduced on the Z9000.

Version
8.3.19.0

Introduced on the S4820T.

Version
8.3.12.0

Introduced on the S4810.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.11.1

Introduced on the S-Series.

Control and Monitoring

141

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Dell Networking S6000 System, Reference Manual, Page: 141 / 1510

Search results

Summary of Contents for Networking S6000 System

Reviews: