Dell Networking S6000 System Reference Manual Download

Page: 1386 / 1510

show storm-control broadcast

Display the storm control broadcast configuration.

S6000

Syntax

show storm-control broadcast [

interface

]

Parameters

interface

(OPTIONAL) Enter one of the following interfaces to display
the interface-specific storm control configuration:

• For a 1-Gigabit Ethernet interface, enter the keyword

GigabitEthernet

followed by the slot/ port

information.

• For a 10-Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

then the slot/port information.

• Fast Ethernet is not supported.

Defaults

none

Command
Modes

• EXEC
• EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.5.1.0

Added support for 4-port 40G line cards on ExaScale.

Version 8.3.7.0

Introduced on the S4810.

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

Version 6.5.1.0

Introduced on the E-Series.

1386

Storm Control

«
...
1384
1385
1386
1387
1388
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands