manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual

Share
Download
Dell Networking S6000 System Reference Manual Download Page 1370

Usage 
Information

When the number of messages reach the limit you set with the 

logging history 

size

 command, older messages are deleted as newer ones are added to the table.

Related 
Commands

show logging

 — displays information logged to the history buffer.

logging monitor

Specify which messages are logged to Telnet applications.

S6000

Syntax

logging monitor [

level

]

To disable logging to terminal connections, use the 

no logging monitor 

command.

Parameters

level

Indicate a value from 0 to 7 or enter one of the following 
parameters: 

emergencies

, 

alerts

, 

critical

, 

errors

, 

warnings

, 

notifications

, 

informational

, or 

debugging

. The default is 

7

 or 

debugging

.

Defaults

7

 or 

debugging

Command 
Modes

CONFIGURATION

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.2(0.0)

Introduced on the M I/O Aggregator. This command is 
supported in Programmable-Mux (PMUX) mode only.

Version 9.0.2.0

Introduced on the S6000.

Version 
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

E-Series legacy 
command

Related 
Commands

default logging monitor

 — returns the logging monitor parameters to the default 

setting.

1370

Simple Network Management Protocol (SNMP) and Syslog

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands