manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual, Page: 1212 / 1510

Share
Download
Dell Networking S6000 System Reference Manual Download Page 1212

hello-time

 — changes the time interval between BPDUs.

protocol spanning-tree rstp

To configure RSTP, enter RSTP mode.

S6000

Syntax

protocol spanning-tree rstp

To exit RSTP mode, use the 

exit

 command.

Defaults

Not configured

Command 
Modes

CONFIGURATION

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

Version 6.2.1.1

Introduced on the E-Series.

Usage 
Information

RSTP is not enabled when you enter RSTP mode. To enable RSTP globally on the 
system, use the 

no disable

 command from RSTP mode.

Example

Dell(conf)#protocol spanning-tree rstp

Dell(config-rstp)##no disable

Related 
Commands

disable

 — disables RSTP globally on the system.

1212

Rapid Spanning Tree Protocol (RSTP)

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments