manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual, Page: 1132 / 1510

Share
Download
Dell Networking S6000 System Reference Manual Download Page 1132

service-policy output

Apply an output policy map to the selected interface.

S6000

Syntax

service-policy output 

policy-map-name

To remove the output policy map from the interface, use the 

no service-

policy output 

policy-map-name

 command.

Parameters

policy-map-
name

Enter the name for the policy map in character format (32 
characters maximum). You can identify an existing policy 
map or name one that does not yet exist.

Defaults

none

Command 
Modes

INTERFACE

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Usage 
Information

A single policy-map can be attached to one or more interfaces to specify the 
service-policy for those interfaces. A policy map attached to an interface can be 
modified.

Related 
Commands

policy-map-output

 — creates an output policy map.

service-queue

Assign a class map and QoS policy to different queues.

S6000

Syntax

service-queue 

queue-id

 [class-map 

class-map-name

] [qos-policy 

qos-policy-name

]

To remove the queue assignment, use the 

no service-queue 

queue-id 

[class-map 

class-map-name

] [qos-policy 

qos-policy-name

] 

command.

1132

Quality of Service (QoS)

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments