Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 1124 / 1510

background image

Usage
Information

To access this command, enter the

class-map

command. After the class map is

identified, you can configure the match criteria.

Related
Commands

— identifies the class map.

match mac vlan

Configure a match criterion for a class map based on VLAN ID.

S6000

Syntax

match mac vlan

number

Parameters

number

Enter the VLAN ID. The range is from 1 to 4094.

Defaults

none

Command
Modes

CLASS-MAP

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 8.2.1.0

Introduced.

Usage
Information

To access this command, enter the

class-map

command. You can match against

only one VLAN ID.

Related
Commands

— identifies the class map.

policy-aggregate

Allow an aggregate method of configuring per-port QoS via policy maps. An aggregate QoS policy is part
of the policy map (output) applied on an interface.

S6000

Syntax

policy-aggregate

qos-policy-name

To remove a policy aggregate configuration, use the

no policy-aggregate

qos-policy-name

command.

1124

Quality of Service (QoS)

«
...
1122
1123
1124
1125
1126
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

Brand: Magnetrol Pages: 12

Brand: Magnetrol Pages: 24

Brand: Daxten Pages: 7

Brand: Movie Vision Pages: 2

Brand: SMC Networks Pages: 2

Brand: Omega Engineering Pages: 8

Brand: Tenda Pages: 177

Brand: LEGRAND Pages: 140

FortiSwitch 424E Series

Brand: Fortinet Pages: 11

CEFLA PIR DALIP

Brand: DANLERS Pages: 2

Brand: Lionel Pages: 8

LiteWave LS105G

Brand: TP-Link Pages: 3

Brand: EtherWAN Pages: 239

Brand: Barksdale Pages: 6

IMI Sensors 691A80

Brand: PCB Piezotronics Pages: 15

SMT-8-...-B Series

Brand: Festo Pages: 2

OmniAccess 6000

Brand: Alcatel-Lucent Pages: 76

Brand: ClimaxDigital Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands