manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual, Page: 1068 / 1510

Share
Download
Dell Networking S6000 System Reference Manual Download Page 1068

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 8.1.1.0

Introduced on the E-Series ExaScale.

Version 7.8.1.0

Introduced on the C-Series for the port-channels and the S-
Series.

Version 7.7.1.1

Introduced

Usage 
Information

This command configures an expiration timer for all S.G entries, unless they are 
assigned to an Extended ACL.

ip pim spt-threshold

To switch to the shortest path tree when the traffic reaches the specified threshold value, configure the 

PIM router.

Syntax

ip pim spt-threshold 

value

 | infinity

To return to the default value, use the 

no ip pim spt-threshold

 command.

Parameters

value

(OPTIONAL) Enter the traffic value in kilobits per second. The 
default is 

10 packets per second

. A value of zero (0) causes a 

switchover on the first packet.

infinity

(OPTIONAL) Enter the keyword 

infinity

 to never switch to 

the source-tree.

Defaults

Not configured.

Command 
Modes

CONFIGURATION

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 
8.3.19.0

Introduced on the S4820T.

1068

PIM-Sparse Mode (PIM-SM)

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments