manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual, Page: 1066 / 1510

Share
Download
Dell Networking S6000 System Reference Manual Download Page 1066

Parameters

interface

Enter the following keywords and slot/port or number 
information:

• For a Gigabit Ethernet interface, enter the keyword 

GigabitEthernet

 then the slot/port information.

• For a Loopback interface, enter the keyword 

loopback 

then a number from 0 to 16383.

• For a Port Channel interface, enter the keywords 

port-

channel

 then a number. The range is from 1 to 128.

• For a 10-Gigabit Ethernet interface, enter the keyword 

TenGigabitEthernet

 then the slot/port information.

• For a VLAN, enter the keyword 

vlan

 then a number from 

1 to 4094.

priority

(OPTIONAL) Enter the priority used in Bootstrap election 
process. The range is zero (0) to 255. The default is 

192

.

Defaults

Not configured.

Command 
Modes

CONFIGURATION

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 8.1.1.0

Introduced on the E-Series ExaScale.

Version 7.8.1.0

Introduced on the S-Series.

pre-Version 
6.1.1.1

Introduced on the E-Series.

Usage 
Information

Priority is stored at BSR router when receiving a Candidate-RP-Advertisement.

ip pim sparse-mode

Enable PIM sparse mode and IGMP on the interface.

S6000

Syntax

ip pim sparse-mode

1066

PIM-Sparse Mode (PIM-SM)

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments