Dell Networking S6000 System Reference Manual Download

Page: 102 / 1510

FTOS(conf)#ip telnet server vrf management

FTOS(conf)#no ip telnet server vrf

ip telnet source-interface

Set an interface’s IP address as the source address in outgoing packets for Telnet sessions.

S6000

Syntax

ip telnet source-interface

interface

To return to the default setting, use the

no ip telnet source-interface

[

interface

]

command.

Parameters

interface

Enter the following keywords and slot/port or number
information:

• For Loopback interfaces, enter the keyword

loopback

then a number from zero (0) to 16383.

• For a Port Channel, enter the keyword

port-channel

then a number. The range is from 1 to 128.

• For a 10-Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

then the slot/port information.

• For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

then the slot/port information.

• For VLAN interface, enter the keyword

vlan

then a

number from 1 to 4094.

• For a tunnel interface, enter the keyword

tunnel

Defaults

The IP address on the system that is closest to the Telnet address is used in the
outgoing packets.

Command
Modes

CONFIGURATION

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

102

Control and Monitoring

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands