Dell Latitude 5430 Service Manual Download Page 48

Page: 48 / 139

Steps

1. Remove the (M2x3.5) screw that secures the WWAN card holder to the system board.
2. Remove the WWAN card holder.
3. Disconnect the antenna cables from the WWAN card.

Table 6. Connectors on the WWAN card

Antenna

Cable Color

Main (white triangle) - ANT1

Orange (cable number 7)

Main (white triangle) - ANT3

White and Black (cable number 6)

Auxiliary (black triangle) - ANT0

White and Grey (cable number 5)

Auxiliary (black triangle) - ANT2

Blue (cable number 8)

4. Slide and remove the WWAN card from the WWAN card slot.

Installing the WWAN card

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

Removing and installing components

Summary of Contents for Latitude 5430












































































































































Search results

Summary of Contents for Latitude 5430

Reviews:

Related manuals for Latitude 5430

Brands by name

Popular brands

Dell Latitude 5430, Service Manual

Search results

Summary of Contents for Latitude 5430

Reviews:

Related manuals for Latitude 5430

Brands by name

Popular brands