Dell Latitude 5430 Service Manual Download

Page: 46 / 139

Table 4. Connectors on the wireless card

Antenna

Cable Color

Main (white triangle)

White (cable number 13)

Auxiliary (black triangle)

Black (cable number 3)

4. Slide and remove the WLAN card from the WLAN card slot.

Installing the WLAN card

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the WLAN card and provides a visual representation of the installation procedure.

Steps

1. Slide the WLAN card at an angle into the WLAN card slot.
2. Connect the antenna cables to the WLAN card. The following table provides the antenna-cable color scheme for the WLAN

card that supports your laptop.

Removing and installing components

Summary of Contents for Latitude 5430












































































































































Search results

Summary of Contents for Latitude 5430

Reviews:

Related manuals for Latitude 5430

Brands by name

Popular brands

Dell Latitude 5430, Service Manual

Search results

Summary of Contents for Latitude 5430

Reviews:

Related manuals for Latitude 5430

Brands by name

Popular brands