manualshive.com logo in svg

Dell Latitude 5401, Service Manual, Page: 22 / 122

Share
Download
Dell Latitude 5401 Service Manual Download Page 22

About this task

The figure indicates the location of the battery in a discrete configuration and provides a visual representation of the installation
procedure.

Steps

1. Place the battery on the palm-rest and keyboard assembly and align the screw holes on the battery with the screw holes on the palm-

rest and keyboard assembly.

2. Install the four screws (M2x3) that secure the battery to the system board and palm-rest and keyboard assembly.
3. Connect the battery cable to the system board.

Next steps

1. Install the

 base cover

.

2. Follow the procedure in 

after working inside your computer

.

WLAN-kaart

Removing the WLAN card - UMA

Prerequisites

1. Follow the procedure in 

before working inside your computer

.

2. Remove the 

base cover

.

3. Remove the 

battery

.

About this task

The figure indicates the location of the WLAN card and provides a visual representation of the removal procedure.

22

Lahtivõtmine ja kokkupanek

Summary of Contents for Latitude 5401



























































































































Reviews:

No comments