manualshive.com logo in svg

Dell Latitude 5401, Service Manual

Share
Download
Dell Latitude 5401 Service Manual Download Page 21

Removing the 4-cell battery - UMA/discrete

Prerequisites

NOTE:

The battery type in your computer varies depending on the configuration ordered.

1. Follow the procedure in 

before working inside your computer

.

2. Remove the

 base cover

.

About this task

The figure indicates the location of the battery in a discrete configuration and provides a visual representation of the removal procedure.

Steps

1. Disconnect the battery cable from the system board.
2. Remove the four screws (M2x3) that secure the battery to the palm-rest and keyboard assembly.
3. Lift the battery off the palm-rest and keyboard assembly.

Installing the 4-cell battery - UMA/discrete

Prerequisites

NOTE:

The battery type in your computer varies depending on the configuration ordered.

If you are replacing a component, remove the existing component before performing the installation procedure.

Lahtivõtmine ja kokkupanek

21

Summary of Contents for Latitude 5401



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands