Dell Latitude 5401 Page 54 Service Manual Download

Page: 54 / 122

Steps

1. Adhere the coin-cell battery to the slot on the palm-rest and keyboard assembly.
2. Route the coin-cell battery cable as illustrated and connect it to the I/O board.

Next steps

1. Install the

battery

2. Install the

base cover

3. Follow the procedure in

after working inside your computer

Removing the coin-cell battery - discrete

Prerequisites

1. Follow the procedure in

before working inside your computer

2. Remove the

base cover

3. Remove the

battery

NOTE:

Removing the coin-cell battery resets the BIOS setup program settings to default. It is recommended that you

note the BIOS setup program settings before removing the coin-cell battery.

About this task

The figure indicates the location of the coin-cell battery and provides a visual representation of the removal procedure.

Steps

1. Disconnect the coin-cell battery cable from the I/O board.
2. Peel the coin-cell battery off the palm-rest and keyboard assembly.

Installing the coin-cell battery - discrete

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

Lahtivõtmine ja kokkupanek

Summary of Contents for Latitude 5401



























































































































Search results

Summary of Contents for Latitude 5401

Reviews:

Related manuals for Latitude 5401

Brands by name

Popular brands

Dell Latitude 5401, Service Manual

Search results

Summary of Contents for Latitude 5401

Reviews:

Related manuals for Latitude 5401

Brands by name

Popular brands