manualshive.com logo in svg

Dell Latitude 5401, Service Manual, Page: 52 / 122

Share
Download
Dell Latitude 5401 Service Manual Download Page 52

Steps

1. Place the heat sink on the system board and align the screw holes on the heat sink with the screw holes on the system board.
2. In sequential order (as indicated on the heat sink), tighten the seven captive screws that secure the heat sink to the system board.

Next steps

1. Install the 

system fan

.

2. Install the 

battery

.

3. Install the 

base cover

.

4. Follow the procedure in 

after working inside your computer

.

Nööppatarei

Removing the coin-cell battery - UMA

Prerequisites

1. Follow the procedure in 

before working inside your computer

.

2. Remove the 

base cover

.

3. Remove the 

battery

.

NOTE:

 Removing the coin-cell battery resets the BIOS setup program settings to default. It is recommended that you

note the BIOS setup program settings before removing the coin-cell battery.

About this task

The figure indicates the location of the coin-cell battery and provides a visual representation of the removal procedure.

52

Lahtivõtmine ja kokkupanek

Summary of Contents for Latitude 5401



























































































































Reviews:

No comments