Dell Latitude 5401 Page 20 Service Manual Download

Page: 20 / 122

Installing the 3-cell battery - UMA/discrete

Prerequisites

NOTE:

The battery type in your computer varies depending on the configuration ordered.

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the 3-cell battery in an UMA configuration and provides a visual representation of the installation
procedure.

Steps

1. Place the battery on the palm-rest and keyboard assembly and align the screw holes on the battery with the screw holes on the palm-

rest and keyboard assembly.

2. Install the four screws (M2x3) that secure the battery to the system board and palm-rest and keyboard assembly.
3. Connect the battery cable to the system board.

Next steps

1. Install the

base cover

2. Follow the procedure in

after working inside your computer

Lahtivõtmine ja kokkupanek

Summary of Contents for Latitude 5401



























































































































Search results

Summary of Contents for Latitude 5401

Reviews:

Related manuals for Latitude 5401

Brands by name

Popular brands

Dell Latitude 5401, Service Manual

Search results

Summary of Contents for Latitude 5401

Reviews:

Related manuals for Latitude 5401

Brands by name

Popular brands