Dell Latitude 5401 Page 13 Service Manual Download

Page: 13 / 122

Lahtivõtmine ja kokkupanek

Teemad:

•

•

•

•

•

•

•

•

•

•

•

•

•

Power button with fingerprint reader (optional)

•

•

•

•

•

Randmetoe ja klaviatuurisõlm

Recommended tools

The procedures in this document may require the following tools:

•

Phillips #0 screwdriver

•

Phillips #1 screwdriver

•

Plastic scribe (recommended for field technicians)

NOTE:

The #0 screw driver is for screws 0-1, and the #1 screw driver is for screws 2-4.

Screw list

NOTE:

When removing screws from a component, it is recommended to note the screw type, the quantity of screws,

and then place them in a screw storage box. This is to ensure that the correct number of screws and correct screw type
is restored when the component is replaced.

NOTE:

Some computers have magnetic surfaces. Ensure that the screws are not left attached to such surface when

replacing a component.

NOTE:

Screw color may vary with the configuration ordered.

Table 1. Screw list

Component

Screw type

Quantity

Screw image

Base cover

M2x8.8 - captive

M2x4

Lahtivõtmine ja kokkupanek

Summary of Contents for Latitude 5401



























































































































Search results

Summary of Contents for Latitude 5401

Reviews:

Related manuals for Latitude 5401

Brands by name

Popular brands

Dell Latitude 5401, Service Manual

Search results

Summary of Contents for Latitude 5401

Reviews:

Related manuals for Latitude 5401

Brands by name

Popular brands