manualshive.com logo in svg

Dell Inspiron 8500, Service Manual, Page: 5 / 75

Share
Download
Dell Inspiron 8500 Service Manual Download Page 5

Before You Begin: Dell Inspiron 8500/8600 Service Manual

6.  To avoid possible damage to the system board, wait 10 to 20 seconds and then disconnect any 

attached devices. 

7.  Disconnect all other external cables from the computer. 

8.  Remove any installed PC Cards from the PC Card slot. 

9.  Close the display and turn the computer upside down on a flat work surface. 

NOTICE: 

To avoid damaging the system board, you must remove the main battery before you 

service the computer. 

10.  Slide and hold the battery-bay latch release on the bottom of the computer, and then remove 

the battery from the bay. 

 

11.  Remove any installed 

memory modules

, 

Mini PCI cards

, and 

modules

, including a second battery 

if one is installed. 

12.  Remove the 

hard drive

. 

Recommended Tools

The procedures in this manual require the following tools:

●

     

#1 Phillips screwdriver

●

     

¼-inch flat-blade screwdriver

file:///I|/SERVICE%20MANUALS/DELL%20MANUALS...WITH%20PARALLEL%20SERIAL_SERV_MAN/begin.htm (2 of 7)6/21/2004 1:12:15 AM

Summary of Contents for Inspiron 8500












































































Reviews:

No comments