Dell Inspiron 7591 2-in-1 Service Manual Download Page 8

Page: 8 / 80

Removing and installing components

Recommended tools

The procedures in this document may require the following tools:

•

Philips screwdriver #1

•

Flat-head screwdriver

•

Plastic scribe

Screw list

NOTE:

When removing screws from a component, it is recommended to note the screw type, the quantity of screws,

and then place them in a screw storage box. This is to ensure that the correct number of screws and correct screw type
is restored when the component is replaced.

NOTE:

Some computers have magnetic surfaces. Ensure that the screws are not left attached to such surface when

replacing a component.

NOTE:

Screw color may vary with the configuration ordered.

Table 1. Screw list

Component

Secured to

Screw type

Quantity

Screw image

Base cover

Palm-rest assembly

M2x4

Battery

Palm-rest assembly

M1.6x4

Battery

Palm-rest assembly

M2x2 Big Head

Fan

Palm-rest assembly

M2x2

Display hinges

Palm-rest assembly

M2x3.5

Keyboard

Palm-rest assembly

M1.2x1.3

Keyboard bracket

Palm-rest assembly

M1.2x1.8

Power-adapter port

Palm-rest assembly

M2x3

Solid-state drive

Palm-rest assembly

M2x2

System board

Palm-rest assembly

M2x2 Big Head

Removing and installing components

Summary of Contents for Inspiron 7591 2-in-1

















































































Search results

Summary of Contents for Inspiron 7591 2-in-1

Reviews:

Related manuals for Inspiron 7591 2-in-1

Brands by name

Popular brands

Dell Inspiron 7591 2-in-1, Service Manual

Search results

Summary of Contents for Inspiron 7591 2-in-1

Reviews:

Related manuals for Inspiron 7591 2-in-1

Brands by name

Popular brands