Dell Inspiron 7591 2-in-1 Service Manual Download Page 23 | Manualshive

Page: 23 / 80

background image

Post-requisites

I/O board

Removing the I/O board

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

Prerequisites

Remove the

Procedure

1. Using the pull tab, disconnect the I/O-board cable from the I/O board.
2. Open the latch and disconnect the fingerprint-reader cable from the I/O board.
3. Disconnect the coin-cell battery cable from the I/O board.
4. Remove the two screws (M2.5x4) that secure the right display hinge to the I/O board.
5. Lift the right display hinge from the I/O board.

Removing and installing components

23

«
...
21
22
23
24
25
...
»

Summary of Contents for Inspiron 7591 2-in-1

















































































Reviews:

No comments

Related manuals for Inspiron 7591 2-in-1

4315 2004 - Aspire

Brand: Acer Pages: 114

3100 1868 - Aspire

Brand: Acer Pages: 113

1410 2039 - Aspire

Brand: Acer Pages: 104

4315 2004 - Aspire

Brand: Acer Pages: 111

4200 4091 - TravelMate - Core Duo 1.66 GHz

Brand: Acer Pages: 110

5050 4697 - Aspire

Brand: Acer Pages: 120

5050 4697 - Aspire

Brand: Acer Pages: 122

4200 4091 - TravelMate - Core Duo 1.66 GHz

Brand: Acer Pages: 81

4200 4091 - TravelMate - Core Duo 1.66 GHz

Brand: Acer Pages: 109

3100 1868 - Aspire

Brand: Acer Pages: 114

3100 1868 - Aspire

Brand: Acer Pages: 116

2480 2779 - TravelMate

Brand: Acer Pages: 95

Brand: Acer Pages: 89

5610 4179 - Aspire

Brand: Acer Pages: 98

5050 4697 - Aspire

Brand: Acer Pages: 120

Toughbook CF-Y5LWEZZBM

Brand: Panasonic Pages: 36

Brand: IBM Pages: 2

Screen Grip-Clip

Brand: Elecrow Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands