Dell Inspiron 7591 2-in-1 Service Manual Download Page 20

Page: 20 / 80

Replacing the wireless card

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

Procedure

CAUTION:

To avoid damage to the wireless card, do not place any cables under it.

1. Connect the antenna cables to the wireless card.

The following table provides the antenna-cable color scheme for the wireless card that is supported by your computer.

Table 2. Antenna-cable color scheme

Connectors on the wireless card

Antenna-cable color

Main (white triangle)

White

Auxiliary (black triangle)

Black

2. Align the notch on the wireless card with the tab on the wireless-card slot and insert the wireless card at an angle into the wireless-

card slot.

3. Align the screw hole on the wireless-card bracket with the screw hole on the wireless card and palm-rest assembly.
4. Replace the screw (M2x3) that secures the wireless-card bracket to the wireless card and palm-rest assembly.

Removing and installing components

Summary of Contents for Inspiron 7591 2-in-1

















































































Search results

Summary of Contents for Inspiron 7591 2-in-1

Reviews:

Related manuals for Inspiron 7591 2-in-1

Brands by name

Popular brands

Dell Inspiron 7591 2-in-1, Service Manual

Search results

Summary of Contents for Inspiron 7591 2-in-1

Reviews:

Related manuals for Inspiron 7591 2-in-1

Brands by name

Popular brands