manualshive.com logo in svg

Dell Inspiron 7300 2n1 Black, Service Manual, Page: 26 / 66

Share
Download
Dell Inspiron 7300 2n1 Black Service Manual Download Page 26

Installing the fan

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

The following image(s) indicate the location of the fan and provides a visual representation of the installation procedure.

Steps

1. Using the alignment posts, place the fan on the palm-rest assembly.
2. Replace the two screws (M2x2) that secure the fan to the palm-rest assembly.
3. Connect the fan cable to the system board.
4. Route the I/O-board cable, speaker cable and antenna cables through the routing guides on the fan.
5. Connect the I/O-board cable to the I/O board and close the latch.
6. Adhere the tape that secures the I/O-board cable-latch to the I/O board.

Next steps

1. Install the 

base cover

.

2. Follow the procedure in 

After working inside your computer

.

Power-adapter port

Removing the power-adapter port

Prerequisites

1. Follow the procedure in 

Before working inside your computer

.

2. Remove the 

base cover

.

26

Removing and installing components

Summary of Contents for Inspiron 7300 2n1 Black



































































Reviews:

No comments