manualshive.com logo in svg

Dell Inspiron 5521, Service Manual

Share
Download
Dell Inspiron 5521 Service Manual Download Page 38

Steps

1. Align and place the battery cable on the battery.
2. Route the battery cable through the routing guides on the battery.
3. Connect the battery cable to the connector on the battery.

Next steps

1. Install the 

base cover

.

2. Install the 

microSD card

.

3. Install the 

SIM card

.

4. Follow the procedure in 

After working on your computer

.

Battery

Lithium-ion battery precautions

CAUTION:

●

Exercise caution when handling Lithium-ion batteries.

●

Discharge the battery completely before removing it. Disconnect the AC power adapter from the system and
operate the computer solely on battery power—the battery is fully discharged when the computer no longer
turns on when the power button is pressed.

●

Do not crush, drop, mutilate, or penetrate the battery with foreign objects.

●

Do not expose the battery to high temperatures, or disassemble battery packs and cells.

●

Do not apply pressure to the surface of the battery.

●

Do not bend the battery.

●

Do not use tools of any kind to pry on or against the battery.

●

Ensure any screws during the servicing of this product are not lost or misplaced, to prevent accidental
puncture or damage to the battery and other system components.

38

Removing and installing components

Summary of Contents for Inspiron 5521























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands