manualshive.com logo in svg

Dell Inspiron 5521, Service Manual

Share
Download
Dell Inspiron 5521 Service Manual Download Page 36

Steps

1. Locate the system board slot on your computer.
2. Align and install the HDD into the computer
3. Replace the four (M2x4) screws that secure the HDD to the computer.
4. Connect the HDD cable on to the connector on the system board.

Next steps

1. Install the 

base cover

.

2. Install the 

microSD card

.

3. Install the 

SIM card

.

4. Exit 

Service Mode

.

5. Follow the procedure in 

After working inside your computer

.

Battery cable

Removing the battery cable

Prerequisites

1. Follow the procedure in 

Before working inside your computer

.

2. Remove the 

SIM card

.

3. Remove the 

microSD card

.

4. Remove the 

base cover

.

NOTE:

 If battery is disconnected from system board for service, then there is a delay during system boot as the system

undergoes RTC battery reset.

About this task

The following images indicate the location of the battery cable and provide a visual representation of the removal procedure.

36

Removing and installing components

Summary of Contents for Inspiron 5521























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands