manualshive.com logo in svg

Dell Inspiron 17 7000 Series, Service Manual

Share
Download
Dell Inspiron 17 7000 Series Service Manual Download Page 97

Replacing the display panel

WARNING: Before working inside your computer, read the safety 
information that shipped with your computer and follow the steps in 

Before 

working inside your computer

. After working inside your computer, follow 

the instructions in 

After working inside your computer

. For more safety best 

practices, see the Regulatory Compliance home page at 

www.dell.com/

regulatory_compliance

.

 

Procedure

1 

Place the display panel on a flat surface.

2 

Replace the 

display cable

.

3 

Replace the 

sensor board

.

4 

Replace the 

camera

.

5 

Turn the display-panel assembly over.

6 

Route the display cable through the routing guide inside the hinge cover.

7 

Align the tabs on the display-panel assembly with the slots on the display back-
cover and antenna assembly and gently snap the display-panel assembly into 
place.

Post-requisites

1 

Replace the 

display assembly

.

2 

Replace the 

wireless card

.

3 

Replace the 

battery

.

4 

Replace the 

base cover

.

97

Summary of Contents for Inspiron 17 7000 Series





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands