manualshive.com logo in svg

Dell Inspiron 17 7000 Series, Service Manual

Share
Download
Dell Inspiron 17 7000 Series Service Manual Download Page 72

Replacing the I/O board

WARNING: Before working inside your computer, read the safety 
information that shipped with your computer and follow the steps in 

Before 

working inside your computer

. After working inside your computer, follow 

the instructions in 

After working inside your computer

. For more safety best 

practices, see the Regulatory Compliance home page at 

www.dell.com/

regulatory_compliance

.

 

Procedure

1 

Using the alignment posts, place the I/O board on the palm-rest assembly.

2 

Align the screw holes on the I/O board with the screw holes on the palm-rest 
assembly.

3 

Replace the two screws (M2x3) that secure the I/O board to the palm-rest 
assembly.

4 

Connect the power and volume-buttons board cable and coin-cell battery cable 
to the I/O board.

5 

Connect the I/O-board cable to the I/O board.

6 

Adhere the tape that secures the I/O-board cable to the I/O board.

Post-requisites

1 

Replace the 

wireless card

.

2 

Replace the 

battery

.

3 

Replace the 

base cover

.

72

Summary of Contents for Inspiron 17 7000 Series





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands