manualshive.com logo in svg

Dell Inspiron 17 5755, Service Manual

Share
Download
Dell Inspiron 17 5755 Service Manual Download Page 92

Replacing the display panel

WARNING: Before working inside your computer, read the safety 
information that shipped with your computer and follow the steps in 

Before working inside your computer

. After working inside your 

computer, follow the instructions in 

After working inside your 

computer

. For more safety best practices, see the Regulatory 

Compliance home page at dell.com/regulatory_compliance. 

 

Procedure

NOTE: These instructions are only applicable for laptop with non-

touchscreen display.

1 

Replace the 

display hinges

.

2 

Slide the display cable into the display-panel cable connector and press 

down the latch to secure the cable.

3 

Adhere the display cable over the display-panel cable connector.

4 

Gently place the display panel on the display back-cover and align the 

screw holes on the display panel with the screw holes on the display 

back-cover.

5 

Replace the screws that secure the display panel to the display back-

cover.

Post-requisites

1 

Replace the 

display bezel

.

2 

Replace the 

display assembly

.

3 

Replace the 

power-adapter port

.

4 

Replace the 

system board

.

5 

Replace the 

heat-sink assembly

.

6 

Replace the 

I/O board

.

7 

Follow the procedure from step 3 to step 8 in “

Replacing the computer 

base

”.

8 

Follow the procedure from step 4 to step 7 in “

Replacing the optical 

drive

”.

9 

Replace the 

keyboard

.

92

Summary of Contents for Inspiron 17 5755













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands