Dell Inspiron 15-3531 Page 12 Service Manual Download

Page: 12 / 83

Removing the Battery

WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in

Before Working Inside Your Computer

. After working inside your

computer, follow the instructions in

After Working Inside Your

Computer

. For more safety best practices, see the Regulatory

Compliance home page at dell.com/regulatory_compliance.

Procedure

Close the display and turn the computer over.

Slide the battery-release latches to the unlock position.

Using your fingertips, lift the battery at an angle and remove the battery

off the battery bay.

battery-release latches (2)

battery

Turn the computer over and open the display as far as possible.

Press and hold the power button for 5 seconds after the computer is

unplugged to ground the system board.

Summary of Contents for Inspiron 15-3531




















































































Search results

Summary of Contents for Inspiron 15-3531

Reviews:

Related manuals for Inspiron 15-3531

Brands by name

Popular brands

Dell Inspiron 15-3531, Service Manual

Search results

Summary of Contents for Inspiron 15-3531

Reviews:

Related manuals for Inspiron 15-3531

Brands by name

Popular brands