Dell Inspiron 14 7000 Series Service Manual Download Page 67

Page: 67 / 90

Removing the Display

Assembly

WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in

Before Working Inside Your Computer

. After working inside your

computer, follow the instructions in

After Working Inside Your

Computer

. For more safety best practices, see the Regulatory

Compliance home page at dell.com/regulatory_compliance.

Prerequisites

Remove the

Remove the

Remove the

Remove the

Remove the

Procedure

Peel off the tape and disconnect the display cable from the system board.

Note the display cable routing and remove the cable from its routing

guide.

Disconnect the antenna cables from the wireless card.

Peel off the tape that secures the antenna cables to the speaker.

Note the antenna cable routing and remove the cables from their routing

guide.

Using the pull-tab, disconnect the I/O-board cable from the I/O board.

Summary of Contents for Inspiron 14 7000 Series



























































































Search results

Summary of Contents for Inspiron 14 7000 Series

Reviews:

Related manuals for Inspiron 14 7000 Series

Brands by name

Popular brands

Dell Inspiron 14 7000 Series, Service Manual

Search results

Summary of Contents for Inspiron 14 7000 Series

Reviews:

Related manuals for Inspiron 14 7000 Series

Brands by name

Popular brands