Dell Inspiron 14 7000 Series Service Manual Download Page 46

Page: 46 / 90

Removing the Coin-Cell

Battery

WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in

Before Working Inside Your Computer

. After working inside your

computer, follow the instructions in

After Working Inside Your

Computer

. For more safety best practices, see the Regulatory

Compliance home page at dell.com/regulatory_compliance.

CAUTION: Removing the coin-cell battery resets the BIOS settings to

default. It is recommended that you note the BIOS settings before

removing the coin-cell battery.

Prerequisites

Remove the

Remove the

Remove the

Remove the

Remove the

Procedure

Using a plastic scribe, gently pry out the coin-cell battery out of the battery

socket on the system board.

Summary of Contents for Inspiron 14 7000 Series



























































































Search results

Summary of Contents for Inspiron 14 7000 Series

Reviews:

Related manuals for Inspiron 14 7000 Series

Brands by name

Popular brands

Dell Inspiron 14 7000 Series, Service Manual

Search results

Summary of Contents for Inspiron 14 7000 Series

Reviews:

Related manuals for Inspiron 14 7000 Series

Brands by name

Popular brands